Swimming Pool and under water Leaks Solutions

Details:-  81 Illingworth Close, Mitcham, Surrey, CR4 3QF, UK  Tel 020 8648 3866     (We stock all products)

All items posted by recorded post



1 Leakmaster Flexible Sealer     "works Underwater"



In stock, Allow 1-3 working days for delivery
£10.99                Colours ;- White or  Blue

Nitrile rubber-based sealant works underwater provides a strong adhesive bond to virtually any material found around the swimming pool...even vinyl. It even repairs vinyl liner leaks with or without a patch. Squeeze from the tube directly onto the material to be sealed. Flexible Sealer will skin over in seconds allowing it to be flattened with a wet finger. Cures and remains flexible in minutes to hours depending on application thickness.

Seal vinyl leaks with or without a patch
Seal between liner and face plates or fittings
Use as thread sealant or seal small suction side plumbing leaks
Seal small cracks in gunite or plaster
Can be applied underwater
Available in blue and white

2 LEAKMASTER Pool Repair Putty     "works Underwater"

  This convenient and versatile epoxy stick adhesivwe and sealant works underwater and cures to a bright white in 20-60 minutes. One stick format eliminates waste and misproportioning. Hundred of used around the pool, homes and busines

Hardens in 20-30 minutes to a fibreglass white

   In stock, Allow 1-3 working days for delivery


3 LEAKMASTER Quick Set Approxy Putty - 5 minute cure


Hand-mouldable epoxy putty in a convenient "one stick" format hardens above or below water to an "off-white" colour. Aggressive adhesiveness and fast 5-minute cure time make Leakmaster Quick Set the logical choice for a multitude of non-cosmetic repairs.


*     Repair cracks in skimmers, main drains and fittings

*      Hardens in 5 minutes for repairs that can't wait

*     Fill cracks in plaster, gunite, fiberglass, or acrylic

*     Pack around light cable to seal leaking light conduit (permanent)

Create a cast around pipe to hold Butyl Tape in place for plumbing leaks




4 Vinyl Swimming Pool Quick Patch     "works Underwater"


Repairs vinyl liners, adheres to wet or dry surfaces covers, enclosures, inflatables, toys, patio umbrellas, table covers, raincoats, life jackets, household items, and vinyl furniture, etc


:- Patches underwater
:- No need to drain pool
:- Transparent pressure sensitive vinyl patch
:- For Underwater & Dry Use
:- Approximate Dimensions: 3" x 3"


5 A+B Epoxy Putty           "works Underwater"


 Two-part, hand-moldable epoxy putty cures in 40-60 minutes to an attractive white. This craftsman quality formulation mixes in your hands to a workable consistency that smoothes and feathers nicely underwater without excessive clouding. A+B is the perfect choice where appearance is important.


Fill and repair cracks in plaster, gunite, fiberglass or acrylic
Repair cracks in skimmers, main drains and fittings
Available in White
In 7 oz Kits

   In stock, Allow 1-3 working days for delivery


6 Mr Sticky's Underwater Glue    "works Underwater"


  Mr. Sticky's Underwater Glue is an amazing adhesive that can actually be applied UNDERWATER. It bonds well to plastics, tile, concrete, stone, fiberglass, rubber, wood and metal. This adhesive is popular for repairs around ponds, pools, spa and marine applications. If it sticks underwater . . . it will bond almost anywhere!
Currently available in a 30 gram manual dual syringe system that dispenses an equal amount of the product that then can be mixed for use.

COLOUR WHITE: Working time is 15-30 minutes, handling time 1-2 hours and cure time 24 hours. Can be applied above or below water.You can use this product to fill gaps, allowing bonding of a smaller fitting into a larger one. With Mr. Sticky's glue PVC pipe can be bonded together without the use of fittings.


   In stock, Allow 1-3 working days for delivery




7 Pool Paste


Colour: White (16 oz. Set)

Typical Applications:

  • Fix hairline cracks
  • Reset tiles on hot tubs, spas, pools
  • Repair cracked skimmers, baskets
  • Replace non-skid strips
  • Repair broken or cracked vacuum brushes or accessories
  • 15 minute working time
  • High-strength epoxy paste
  • Does not run…Stays where you put it
  • Paint can be applied after light sanding


POOL PASTE particularly for setting tiles on hot tubs, spas and pools, with the added benefit of setting quicklywhen time is a factor.It can be used to repair hairline cracks in plastic pipe, concrete, fiberglass and wood and to repair saunas or whirlpools. It is also specially formulated for adhesion to plastics. Easily mixed, 1-to-1, it bonds glass, wood,
steel, iron and ceramics.
EPOXYBOND POOL PASTE can be painted after light sanding.
Working Life (min.)15-35
Setting Time 12hr


8 Waterproof Sealant 





Concrete Applications:

  • Waterproof basement walls and floors, garage floors
  • Stop leaks and water seepage in swimming pools, sidewalks, driveways, patios

Marine Applications:

  • Seals & fills leaks & cracks on all wooden surfaces
  • Two-part, high-solids, liquid epoxy
  • Apply on dry or damp surfaces of wood, fiberglass, concrete, steel, aluminum
  • Excellent adhesion and wear properties
  • Paint can be applied after light sanding


Pour the entire contents of the smaller container (Hardener) into the larger can containing the Resin
and mix thoroughly. Mix must be used within 30 minutes at 70F (21C) to 80 F (27C) or contents will
harden in the can. Apply a heavy coat with a 2" to 3" paint brush over the problem areas. Allow 10 hours for drying at 75 F (24C). At temperatures below 75 F(24C), drying time will be extended. DO NOT APPLY WHEN TEMPERATURE IS BELOW 60 F (16C)


Below Grade Walls and Floors - In basements, water seepage usually occurs at the wall-floor
intersection. A heavy coating of EPOXYBOND WATERPROOF SEALANT should be applied at the
junction of the wall and floor extending at least 6 inches onto the floor and at least one block high on the wall. If the area of leakage can be pinpointed, extend the coating at least three inches past this point. On porous surfaces, such as cinder block, coverage will be less (approximately 25 sq. ft. per one quart unit).
Two coats are recommended. Apply second coat within 48 hours. If second coat is applied after 48
hours, the surface must first be sanded and cleaned. Although EPOXYBOND WATERPROOF SEALANT
can be applied to a damp surface, the drier the surface being coated, the better the protection. Flowing water must be sealed with a quick setting hydraulic cement before applying EPOXYBOND WATERPROOF SEALANT.

Outdoor Applications
- Apply a topcoat using a good commercially available outdoor paint because
ultraviolet rays from the sun will cause chalking and embrittlement. EPOXYBOND WATERPROOF
SEALANT may be painted after allowing to dry for 24 hours. Prior to painting, wash the surface with soap and water. After it has been in place for more than one week or if exposed to excessive high humidity during application, a blush may appear on the surface.







   In stock, Allow 1-3 working days for delivery
These convenient syringe-style testers are charged with a special concentrated dye that holds
Together underwater. Six-inch plastic "needle" allows for precise dye placement without creating
Unwanted currents.
• Identify the precise location of structural pool leaks
• Identify water movement into or out of pipes
• Available in blue 



10 Fix-A-Leak


£45.99  Size 32oz         

Marlig Fix-A-Leak is a blended concentrated liquid material designed to permanently seal small leaks & holes up to 1/8" diameter in spa shells and swimming pool plumbing - quickly & inexpensively. Safe & easy to use, Marlig Fix-A-Leak has been thoroughly field-tested under various weather conditions, and has proven to be safe & extremely effective.

: seal leaks in pool and bath tubs
: is a blended concentrated material designed to seal leaks in virtually any material
: can be applied for leaks in the shell and works equally well in plumbing
: will seal holes 1/8" in diameter
: will form a permanent seal

Marlig Fix-A-Leak is also great for preventative maintenance, to coat surfaces and cut down on formation of rust & corrosion. Dosage is 8 oz. per 1,000 gallons for minor leaks; use a second bottle for larger leaks. Treatment can be repeated if necessary. Do not use in excess of 1 quart per 5000 gallons of water. Available in both 8-oz. and 32-oz. sizes.


Directions (Shake Well Before Using)

  1. Bypass FILTER MEDIA before adding Fix-A-Leak to water. Sand Filters: set filter valve to recirculate Other Types: remove cartridges DE elements from filter tank. Then proceed to circulate through empty tank.
  2. With pump running add Fix-A-Leak slowly through skimmer or in front of any other suction intake.
  3. After adding Fix-A-Leak adjust suction to main drain. If this is not possible, the vacuum cleaner could be used alternatively, simply by placing the vacuum in deepest part of pool and connect to normal vacuum connection. Set filter valve to normal vacuum position.
  4. Fix-A-Leak is very heavy and will sink to the lowest point rather quickly. It must be stirred back into suspension, either manually using a pool broom or mechanically with an automated pool cleaner every 4-6 hrs. during circulation of water.
  5. Continue to recirculate water until the leak has stopped.
  6. Mark level of water in pool and check for 2-3 days to determine if the leak has stopped.
  7. After the leak has stopped and given the proper time to cure, (24-48 hrs.) you may return to normal filtration. Sand filters: Set filter valve to filter and resume normal operation. Backwash out unused Fix-A-Leak as required. Other Filters: Reinstall filter into tank and Resume operation. Rinse out unused Fix-A-Leak from filter as required.*NOTE* Never let cartridges or DE elements be left to dry before they are cleaned.
  8. Treatment can be repeated if necessary.


If you suspect a leak around fittings inside the pool (such as return fittings) lights, skimmer(s) or steps, etc.Shut down pump.

Apply FIX-A-LEAK directly to the leak using a squeeze bottle, similar to a ketchup bottle. Allow a minimum of 48 hrs. to cure before starting up circulation.

For Bath Tubs

Once you determine the leak has stopped, drain your tub. Properly wipe down the spa with a wet cloth, nothing abrasive. Allow to dry for 4-5 days to all FIX A LEAK to properly cure.



11 LEAKMASTER 15' Single Roll Butyl Tape     "works Underwater"


Hand-moldable rubber gap filler can be applied underwater without messy caulk guns or mixing. Retains a flexible, tacky consistency making it well suited for a variety of permanent or temporary leak-stopping applications.


  • Pack around light cable to seal or prevent leaking light conduit (removable)
  • Replace rubber gaskets with or without out removing fitting
  • Fill/seal cracks, gaps or voids
  • Hold in place with a cast of Quick Set Epoxy for pipe repairs

BT15 Individually Boxed 15' Roll


   In stock, Allow 1-3 working days for delivery






WATERWELD will plug or seal practically anything that leaks. It will patch holes and cracks, and mend almost anything that is broken. It is excellent for rebuilding or fabricating parts, and as an all-purpose adhesive for metals, wood, fiberglass, masonry, ceramics, PVC and ABS. Permanently repair holes, gouges, cuts ... even seals rot in fiberglass and wood. Cures under water. Safe for use on lines carrying potable water. We should really call this amazing product "The Miracle Welder," because you can use it to plug holes and make permanent repairs under water and in gas tanks -- while they're still leaking. No exaggeration -- this is the best epoxy putty you can use material.

WATERWELD can be applied under water; surfaces to be repaired do not need to be clean and dry. WATERWELD putty "mushrooms" through and around holes, grabbing the edges to hold securely, then hardening for a permanent seal



13 H20 Glue Underwater Adhesive and sealant








Professional two-part adhesive and sealant used to repair and seal pools,
Fountains, spa's, sprinklers, health spas and therapy centres. Use this product if you maintain an aquatic centre, golf course, arboretum, Water Park, water slide or irrigation systems.

H2O Glue is packaged in easily applied dual cartridge system. Cartridges and static mixers are designed to work together as an integrated high performance system.

There are hundreds of uses for H2O Glue.
Repair slides and pools underwater with a cure time of 30-45 minutes!
There are hundreds of uses for our H2O Glue® adhesive. Repairs are made easier by applying to wet or dry surfaces. Provides a hand-able bond in 30-45 minutes. Full cure in 24 hours. With our easily applied H2O Glue® two part adhesive there is no need to drain the pool to do the repairs. H2O Glue® has thousands of uses and no job is to big or to small!

• Leaks around drains
• Pool and Spa Maintenance
• Pump or Hose Leaks
• Repair Fibreglass and PVC

Kit #2 Contains:
Caulk Gun Adapter
50ML Cartridges Pack
2 Static Mixers



   In stock, Allow 1-3 working days for delivery



14 DAP Household/Aquarium Adhesive Sealant

Long-lasting 100% silicone rubber sealant provides a strong waterproof seal that won't crack or shrink. Ideal for quick household repairs and projects, as well as building and repairing aquariums. Harmless to fresh and saltwater fish. Safe for food contact. Dishwasher and microwave safe. Colour - Clear.

   In stock, Allow 1-3 working days for delivery






13 DuraPower Product's Patch Kit       "Works on wet surfaces".


DuraPower Product's Patch Kit is a Two-Part epoxy Fiberglass Repair Kit

The Patch Kit is especially designed for flat surfaces, such as tanks, containers, boat hulls, or large diameter pipes. This Special patch is easy to use...no measuring, no mess, and no external clean-up. Just blend the components together in the package and apply to any clean surface...It will cure in approximately 20 minutes- even on wet surfaces.

Key BenefitsDoes not required sun to cure, pre-measured two part epoxy , easy to use no external clean-up, f lat surface repair & pipes

4" X 6" £8.99
2" X 20" £9.99
4" X 12" £9.99

Patch Kit - 4" X 6" £8.99

Patch Kit - 2" X 20" £9.99
Patch Kit - 4" X 12" £9.99


16 Plast-aid Acrylic and PVC  Multi Purpose Repair Kit


Size 1.5oz £14.99

   In stock, Allow 1-3 working days for delivery

Size 6oz £24.99

   In stock, Allow 1-3 working days for delivery

Plast-aid®, the exciting new multi-purpose repair plastic used for thousands of repair solutions! Unlike anything on the market today, Plast-aid® forms a hard, durable, waterproof plastic in only
Plast-aid® is a two part compound consisting of a liquid and powder. When combined, Plast-aid®'s unique curing process begins. As it thickens, Plast-aid® transforms from a castable liquid, to a glue, to a putty, to a clay, and finally to a hard, durable, waterproof plastic. This progression makes Plast-aid® an incredibly versatile tool allowing it to be cast into molds, used to repair breaks and fill gaps, formed into shapes for custom parts, and much, much more!
Colour Plast-aid® with artist acrylic or wood stain.
After Plast-aid® cures, drill, cut, file & polish your custom parts

For Car
From fixing cracked panels & fenders, to stripped knobs, to broken light lenses

Pool and Spa

Repair pools & spas, hot tub, skimmers, holes, cracks, leaky PVC, ABS, Acrylic, etc.

Plast-aid® repairs are fast, waterproof & permanent

Unsurpassed for PVC plumbing repair! Don't cut out damaged PVC, simply & permanently patch it with Plast-aid® in only 15 minutes!
Make custom fittings & threaded adaptors

Fix everything from dropped cell phones, remote controls & hair dryers to stripped out hinges, broken toys, computer housings & refrigerator shelves
Repair broken items and create custom parts with one product!
Use Silly® Putty to make molds of ornate knobs, Cast the molds with colour Plast-aid®. Fill cracks.
Use on model planes, trains & boats

17 Kraken Silicone Repair Tape  (Stays Flexible)     "Stop leaks, works on wet surfaces".




Kraken Tape is a self-fusing 'wrap & repair' silicone based tape. Simply stretch & wrap to repair water/plumbing leaks, insulate cables, seal & secure connectors, bind rope ends to prevent fray, exhaust & automotive repair and much more.
The Ultimate Multi-Purpose Repair Tape. Fast fusing silicone, seals and repairs an almost endless list of pipes, connectors, joints and so much more.


 In the Home
• Water Pipes
• Drains
• Guttering
• Sink & Bath Connectors
• Joints & Seals
 In the Car & Boat
• Radiator Hoses
• Cables & Connectors
• Exhaust Repair
• Oil Lines
• Water Hoses/pipes

Up to 700psi Tensile Strength, -65C to 260C Temperature Range
up to 7,000V Dielectric Strength

24mm x 3.6m      £8.99
48mm x 10.9m    £19.99

24mm x 3.6m £8.99

48mm x 10.9m £19.99



19 Underwater Magic  - UNDERWATER Adhesive & Sealant





£23.99    Colour - White or Blue


Underwater Magic is an extremely strong single component adhesive and sealant, designed for a wide variety of tasks in and around wet areas and UNDERWATER.
Free from isocyanate & solvents
100% Silicone free, instantly rainproof,
sea & chlorine water resistant.

• Indoor and outdoor pools in full water contact.
• Fixing and replacement of tiles filling new joints
• Fixing or new joints at the edge of the pool
• Piping and building armatures
• In the insulation technology
• Repair and maintainance in and around wet areas
• Repair of Fish Tanks & Ponds etc 

Underwater magic bonds and seals alot of materials:
• Plastics
• Styrofoam
• Metals
• Wood
• Glass and Glass Tiles & Mosaic
• Ceramic and Ceramic Tiles and Mosaic
• Stone, Granite, Conquered…..
Can be bond to each other!!!

Excellent addition on most surfaces without a Primer

Is not affected by:
• Chlorine / salt (sea) water
• Weathering and UV light
• Aliphatic solvents, oils, grease, diluted inorganic acids and alkalis
• Permanently elastic and with good abrasion resistance
• good mechanical properties
• Temperature resistant from - 40°C degrees to +90°C
• For a short time ( 2 to 3 hours) even to +200°C




1 Akfix ALLBOND MS HIGH TACK - Adhesive & Sealant

Akfix All Bond MS High Tack is a MS polymer-based, one component, high quality and professional adhesive with high adhesive strength and initial tack. It is suitable for bonding heavy building materials without the use of clamps and/or fixing tape.

High initial grab


PC Concrete™ epoxy gel is an anchoring and


Akfix ALLBOND MS HIGH TACK - Adhesive & Sealant £9.99


    High initial grab,
    Does not contain solvent, silicone or isocyanate,
    Wooden and plastic laths, ornaments and frames
    Doorsteps, window sills, skirting boards and cover plates
    Complete construction elements (such as roofing and facade elements) in frame
    Semi-elastic bonding,
    Very good UV resistance
    Excellent elasticity and very good adhesion strength
    Over-paintable with water based paints,
    No bubble formation
    No shrinkage
    Primer less adhesion on many different substrates (preliminary test recommended)
    Wall cladding elements and ceiling panels
    Sound isolation panels (mineral wool, wood-wool cement & plastic foams)
    Thermal isolation panels (PUR, PIR, PS)
    Casings and frames in building construction
    Wooden and plastic laths, ornaments and frames
    Doorsteps, window sills, skirting boards and cover plates
    Complete construction elements (such as roofing and facade elements) in frame