Details:-  81 Illingworth Close, Mitcham, Surrey, CR4 3QF, UK  Tel 020 8648 3866     (We stock all products)

All items posted by recorded post

1 Waterproof Sealant 





Concrete Applications:

  • Waterproof basement walls and floors, garage floors
  • Stop leaks and water seepage in swimming pools, sidewalks, driveways, patios

Marine Applications:

  • Seals & fills leaks & cracks on all wooden surfaces
  • Two-part, high-solids, liquid epoxy
  • Apply on dry or damp surfaces of wood, fiberglass, concrete, steel, aluminum
  • Excellent adhesion and wear properties
  • Paint can be applied after light sanding


Pour the entire contents of the smaller container (Hardener) into the larger can containing the Resin
and mix thoroughly. Mix must be used within 30 minutes at 70F (21C) to 80 F (27C) or contents will
harden in the can. Apply a heavy coat with a 2" to 3" paint brush over the problem areas. Allow 10 hours for drying at 75 F (24C). At temperatures below 75 F(24C), drying time will be extended. DO NOT APPLY WHEN TEMPERATURE IS BELOW 60 F (16C)


Below Grade Walls and Floors - In basements, water seepage usually occurs at the wall-floor
intersection. A heavy coating of EPOXYBOND WATERPROOF SEALANT should be applied at the
junction of the wall and floor extending at least 6 inches onto the floor and at least one block high on the wall. If the area of leakage can be pinpointed, extend the coating at least three inches past this point. On porous surfaces, such as cinder block, coverage will be less (approximately 25 sq. ft. per one quart unit).
Two coats are recommended. Apply second coat within 48 hours. If second coat is applied after 48
hours, the surface must first be sanded and cleaned. Although EPOXYBOND WATERPROOF SEALANT
can be applied to a damp surface, the drier the surface being coated, the better the protection. Flowing water must be sealed with a quick setting hydraulic cement before applying EPOXYBOND WATERPROOF SEALANT.

Outdoor Applications
- Apply a topcoat using a good commercially available outdoor paint because
ultraviolet rays from the sun will cause chalking and embrittlement. EPOXYBOND WATERPROOF
SEALANT may be painted after allowing to dry for 24 hours. Prior to painting, wash the surface with soap and water. After it has been in place for more than one week or if exposed to excessive high humidity during application, a blush may appear on the surface.


2 Thompson's One Coat Damp Seal

  Thompson's One Coat Damp Seal is a high performance interior seal developed to form a breathable, obliterating membrane that seals and permanently stops the reappearance of damp, water and other household stains. Suitable for application to both dry and damp walls and ceilings the micro-porous formulation allows trapped moisture to evaporate to prevent paint flaking or wallpaper peeling off. Full coverage can be achieved in just one coat, ensuring the surface is prepared for decoration in as little as 4 hours. Suitable for use on interior walls or ceilings, including plaster, cement and stone. Apply liberally working well over the affected region and surrounding area (approximately 30cm beyond the affected area)



3 Ronseal One Coat Anti Damp Paint


With Ronseal One Coat Anti-Damp Paint, stains don't have to be a pain. In one coat, it quickly and easily covers damp, water and other household stains - it can even be applied to damp surfaces. You can paint or wallpaper over it and is guaranteed to block damp permanently.

  • Apply direct to damp walls and ceilings
  • Permanently blocks stains
  • Smooth white finish
  • Can be painted or wallpapered over


  • Areas of use: Interior walls & ceilings
  • Coverage: 5 m2 covered per litre
  • Number of coats: 1
  • Finish: smooth white
  • Application: Brush
  • Drying time: 2 hours


 Size  250m   -  Colour White






4  Thompson's Stain Block Aerosol Spray

   Thompson's Stain Block Aerosol is the quick and easy no mess solution to obliterate unsightly stains preventing them from reappearing. Dry in only 10 minutes, stain block can be used on both walls and ceilings to obliterate the stains. Suitable for use on interior walls or ceilings, including plaster, cement and stone. Touch dry in 10 minutes. Shake well until mixing ball rattles and continue for one minute. Shake can occasionally during use. Hold can 9"-12" (20-30cm) away from stained area, commence spraying, moving can in a motion from left to right or up and down until the area is covered with an even coat. Allow to dry fully and apply a second coat if required. When completely dry, surfaces can be painted or wallpapered over.

Thompson's Water Seal


Thompson's Water Seal utilises hydrophobic technology to deliver invisible protection against water damage. The deep penetrating formulation travels deep into exterior dry porous surfaces to form a breathable membrane that allows moisture vapour inside the substrate to evaporate whilst protecting against water penetration and damage. Thompson's Water Seal has a unique formulation which, unlike some waterproofers, penetrates the surface therefore waterproofing even after the initial beading is gone. It will not be destroyed by ultraviolet light and is long lasting even under heavy moisture conditions. Assuming application instructions and coverage guidelines are adhered to it provides effective water repellency for years.

Suitable for use on brick, concrete, stone and wood. For exterior use only


 1 Litre  -  Colour Clear